A Variable Speed Synchronous Motor Approach for Smart Irrigation using Doubly Fed Induction Motor

Authors

  • Emad Hassan Department of Electronics and Electrical Communications, Faculty of Electronic Engineering, Menoufia University, Menouf 32952, Egypt
  • Ahmed S. Oshaba Department of Electrical Engineering, College of Engineering, Jazan University, Jizan 45142, Saudi Arabia
  • Dina S. M. Osheba Department of Electrical Engineering, Menoufiya University, Shebin El-kom 32511, Egypt.
  • Mervet A. Shanab Department of Electrical Engineering, Menoufiya University, Shebin El-kom 32511, Egypt.

DOI:

https://doi.org/10.17981/ingecuc.19.2.2023.02

Keywords:

doubly fed induction motor, synchronous motor, smart irrigation, steady state performance

Abstract

Introduction— Doubly Fed Induction Motor (DFIM) is a popular machine used in variable speed drives, and its ruggedness, reliability and simplicity of speed control make it a suitable candidate for use in smart irrigation systems.

Objective— This paper studies and evaluates the performance of DFIM at different operating conditions and shows that it can be viewed as a variable speed synchronous motor.

Methodology— A mathematical model has been developed to optimize the performance of the DFIM in smart irrigation systems, taking into account the specific conditions of the application. In addition, an experimental setup was built and tested to enhance the theoretical results, which showed good correlation between the theoretical and experimental results.

Results— The research results reveal that DFIM can be used to control the flow rate of water in irrigation systems, by adjusting the speed of the motor to match the desired flow rate.

Conclusions— The results of this research demonstrate the potential of using the DFIM in smart irrigation systems to improve the performance and efficiency of irrigation and to provide better control and lower costs.

Downloads

Download data is not yet available.

References

M. Etemadi, H. Hesar & M. Khoshhava, “Speed Control of Brushless Doubly Fed Induction Machine Drive Based on Model Reference Adaptive System,” presented at 13th Power Electronics, Drive Systems, and Technologies Conference, PEDSTC, THR, IR, 1-3 Feb. 2022. https://doi.org/10.1109/PEDSTC53976.2022.9767330

Y. Zhang, J. Ge, W. Xu, W. Li, Y. Luo, S. Su, & Y. He, “Performance Analysis of Nested-loop Secondary Linear Doubly-fed Machine Considering End Effects,” CES Trans Electr Mach Syst, vol. 6, no. 3, pp. 298–305, Sept. 2022. https://doi.org/10.30941/CESTEMS.2022.00040

Z. Cheng, Z. Cao, J. Hwang & C. Mi, “A Novel Single-Turn Permanent Magnet Synchronous Machine for Electric Aircraft,” Energies, vol. 16, no. 3, pp. 1–14, Jan. 2023. https://doi.org/10.3390/en16031041

N. El Ouanjli, A. Derouich, A. El Ghzizal, J. Bouchnaif, Y. El Mourabit, M. Taoussi & B. Bossoufi, “Real-time implementation in dSPACE of DTC-backstepping for a doubly fed induction motor,” Eur. Phys. J. Plus, vol. 134, no. 11, pp. 1–14, Aug. 2019. https://doi.org/10.1140/epjp/i2019-12961-x

R. Yang, Z. He, N. Sugita & T. Shinshi, “Low-Cost and Compact Disposable Extracorporeal Centrifugal Blood Pump Utilizing a Homopolar Bearingless Switched Reluctance Slice Motor,” IEEE Access, vol. 11, pp. 24353–24366, Mar. 2023. https://doi.org/10.1109/ACCESS.2023.3254546

D. Li, G. Gong, J. Lv, X. Jiang & R. He, “An Overall Control of Doubly fed Variable Speed Pumped Storage Unit in Pumping Mode,” presented at IEEE 4th Conference on Energy Internet and Energy System Integration, EI2, WHN, CN, 30 Oct. 2020 - 1 Nov. 2020. https://doi.org/10.1109/EI250167.2020.9346705

R. Selvaraj, T. Chelliah & K. Desingu, “Reactive Power Circulation Based Fault Tolerance Schemes for Multi-Megawatt 3L-NPC Paralleled Converters in Variable Speed Hydro Applications,” IEEE Trans Ind Appl, vol. 59, no. 2, pp. 1923–1934, Mar. 2023. https://doi.org/10.1109/TIA.2022.3222647

R. Mehrjardi, N. Ershad, B. Rahrovi & M. Ehsani, “Brushless Doubly-Fed Induction Machine with Feed-Forward Torque Compensation Control,” presented at IEEE Texas Power and Energy Conference, TPEC, CS, TX, USA, 2-5 Feb. 2021. https://doi.org/10.1109/TPEC51183.2021.9384974

W. Rajan Babu, M. Sundaram, G. Muthuram, A. Khaja Najumudeen, M. Karthick & B. Chandramouli, “MSCP based Rotor Faults and Mechanical Bearing Failure Identification in Induction Motor using Power Quality Analyzer,” presented at International Conference on Intelligent Data Communication Technologies and Internet of Things, IDCIoT, BGLU, IN, 5-7 Jan. 2023. https://doi.org/10.1109/IDCIoT56793.2023.10053456

M. Yahiaoui, M. Kinnaert & J. Gyselinck, “Sensorless Vector Control for Grid Synchronization of Doubly-Fed Induction Generators,” presented at International Conference on Electrical Machines, ICEM, VAL, ES, 5-8 Sept. 2022. https://doi.org/10.1109/ICEM51905.2022.9910913

C. Djamila, M. Yahia & M. Mohamed, “Performances of Robust Control of Doubly-Fed Induction Generator for Wind Energy Conversion System,” presented at 2nd International Conference on Innovative Research in Applied Science, Engineering and Technology, IRASET, MKS, MOR, 3-4 Mar. 2022. https://doi.org/10.1109/IRASET52964.2022.9737917

R. Ryndzionek, K. Blecharz, F. Kutt, M. Michna & G. Kostro, “Fault-Tolerant Performance of the Novel Five-Phase Doubly-Fed Induction Generator,” IEEE Access, vol. 10, pp. 59350–59358, May. 2022. https://doi.org/10.1109/ACCESS.2022.3179815

S. Abdi, E. Abdi & H. Toshani, “Rotational Iron Losses in Brushless Doubly Fed Machines,” presented at International Conference on Electrical Machines, ICEM, VAL, ES, 5-8 Sept. 2022. https://doi.org/10.1109/ICEM51905.2022.9910940

B. Battulga, M. Shaikh, S. Bin Lee & M. Osama, “Automated Detection of Failures in Doubly-Fed Induction Generators for Wind Turbine Applications,” presented at IEEE Energy Conversion Congress and Exposition, ECCE, DET, MI, USA, 9-13 Oct. 2022. https://doi.org/10.1109/ECCE50734.2022.9947734

M. Cheng, X. Yan & J. Zhou, “Negative-Sequence Current Compensation-Based Coordinated Control Strategy for Dual-Cage-Rotor Brushless Doubly Fed Induction Generator Under Unbalanced Grid Conditions,” IEEE Trans Ind Electron, vol. 70, no. 5, pp. 4762–4773, May. 2023. https://doi.org/10.1109/TIE.2022.3186317

F. Deylami & A. Darabi, “A Simple Method for Steady-State Performance Optimization of Doubly-Fed Induction Machines,” presented at 9th Iranian Conference on Renewable Energy & Distributed Generation, ICREDG, MSHD, IR, 23-24 Feb. 2022. https://doi.org/10.1109/ICREDG54199.2022.9804516

M. Mehta & B. Mehta, “Implementation of STATCOM in a Doubly Fed Induction Machine Based Wind Park,” presented at IEEE International Power and Renewable Energy Conference, IPRECON, KLLM, IN, 16-18 Dec. 2022. https://doi.org/10.1109/IPRECON55716.2022.10059544

S. Odhano, S. Rubino, M. Tang, P. Zanchetta & R. Bojoi, “Stator Current-Sensorless-Modulated Model Predictive Direct Power Control of a DFIM With Magnetizing Characteristic Identification,” IEEE J Emerg Sel Top Power Electron, vol. 9, no. 3, pp. 2797–2806, Jun. 2021. https://doi.org/10.1109/JESTPE.2020.3024679

B. Dahhou & A. Bouraiou, “Speed Control Of DFIM Using Artificial Neural Network Controller,” presented at 2nd International Conference on Advanced Electrical Engineering, ICAEE, COST, AG, 29-31 Oct. 2022. https://doi.org/10.1109/ICAEE53772.2022.9961983

L. Simon, J. Ravishankar & S. Swarup, “Coordinated reactive power and crow bar control for DFIG-based wind turbines for power oscillation damping,” Wind Eng, vol. 43, no. 2, pp. 95–113, Jul. 2018. https://doi.org/10.1177/0309524X18780385

Downloads

Published

2023-04-24

How to Cite

Hassan, E., S. Oshaba, A. ., M. Osheba, D. S. ., & A. Shanab, M. (2023). A Variable Speed Synchronous Motor Approach for Smart Irrigation using Doubly Fed Induction Motor. INGE CUC, 19(2), 21–32. https://doi.org/10.17981/ingecuc.19.2.2023.02

Issue

Vol. 19 No. 2 (2023): (Julio-Diciembre)

Section

In Press

License

Copyright (c) 2023 INGE CUC

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Published papers are the exclusive responsibility of their authors and do not necessary reflect the opinions of the editorial committee. 

INGE CUC Journal respects the moral rights of its authors, whom must cede the editorial committee the patrimonial rights of the published material. In turn, the authors inform that the current work is unpublished and has not been previously published. 

All articles are licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Licencia Creative Commons